EN1092-1/01B PN10

FLANSCHE AUS EDELSTAHL 1.4301 (AISI 304)

EN1092-1/01B PN10

EN1092-1/01B PN10

Stufen-Flachflansch aus Edelstahl A304

Technical specification

TOLERANCES (according to UNI 6100-67)

DIMENSION SIZE TOLERANCES
D
Outside diameter
≤ DN 200 ± 1,0
> DN 200 ≤ DN 300 ± 1,5
> DN 300 ≤ DN 400 ± 2,0
> DN 400 ± 2,0
d1
Outside diameter of neck
≤ DN 100 +0,5 -0
> DN 100 ≤ DN 400 +1,0 -0,5
> DN 400 +1,5 -1,0
d1
Bore diameter
≤ DN 80 +0,5 -0
> DN 80 ≤ DN 350 +1,0 -0
> DN 350 ≤ DN 400 +1,5 -0
> DN 400 +5
b
Thickness
≤ DN 10 ± 0,5
> DN 10 ≤ DN 20 ± 0,8
> DN 20 ≤ DN 50 ± 1,0
> DN 50 ± 1,5
d3
Neck diameter
+1 -0
h1
Length through hub
≤ DN 80 ± 1,5
> DN 80 ≤ DN 250 ± 2,0
> DN 250 ± 3,0
S
Wall thickness
≤ DN 100 +1,0 -0
> DN 100 ≤ DN 400 +1,5 -0
> DN 400 +2,0 -0
d4
Diameter of contact face
≤ DN 80 +0 -1,0
> DN 100 ≤ DN 400 +0 -2,0
> DN 400 +0 -3,0
k
Diameter of bolt circle
≤ DN 250 ± 1,5
> DN 250 ≤ DN 600 ± 2,0
> DN 600 ± 3,0
Centre-to-centre of adjacent bolt holes ± 0,4
Max. eccentricity between bolt circle dia. K and machined facing diameters +0,8 -0
Surface parallelism
d2
Holes diameter
≤ DN 300 +2 -0
> DN 30 +3 -0

DIMENSIONAL TOLERANCES (ANSI B 16.5)

D Outside Diameter* Slip-on, Blind and Welding neck flanges When OD is 24" or less ±1,6 mm
When OD is over 24" ±3,2 mm
J Inside Diameter Slip-on flanges 10" and smaller +0,8 mm
12" and larger +1,6 mm
Inside Diameter** Welding neck flanges 10" and smaller +0,8 mm
12" to 18" +1,6 mm
20" and larger +3,2 mm -1,6 mm
g Diameter of Contact Face Slip-on, Blind and Welding neck flanges 1,6 mm Raised Face ±0,8 mm
6,4 mm Raised Face ±0,5 mm
a Diameter of Hub at Point of Welding Welding neck flanges 5" and smaller +2,4 mm -0,8 mm
6" and larger +4,0 mm -0,8 mm
m Outside Diameter of Hub* Slip-on and Blind flanges 12" and smaller +2,4 mm -1,6 mm
14" and larger ±3,2 mm
Diameter of Hub at Base* Welding neck flanges When Hub Base is 24" or less ±1,6 mm
When Hub Base is over 24" ±3,2 mm
i Drilling and facing Slip-on, Blind and Welding neck flanges Bolt Circle Diameter k 1,6 mm
Center-to-center of adjacent bolt holes ±0,8 mm
mmMax. eccentricity between bolt circle dia. kand machined facing diameters  
 
sizes 2½" and smaller 0,8 mm
sizes 3" and larger 1,6 mm
h Overall Length of Hub Slip-on and Blind flanges 18" and smaller +3,2 mm -0,8 mm
20" and larger +4,8 mm -1,6 mm
Welding neck flanges 10" and smaller ±1,6 mm
12" and larger ±3,2 mm
b Thickness Slip-on, Blind and Welding neck flanges 18" and smaller +3,2 mm
20" and larger +4,8 mm

* This tolerance is not covered by ANSI B 16.5

** Undependent of the tolerances of the measures J and a, the wall thickness shall not be less than 87,5% of the nominal wall thickness

TOLERANCES (according to EN 1092-1:2007)

Dimension Flange type Size Tolerance mm
Outside diameter of neck d1 11 ≤DN 125 0 to +3,0
>DN 125 ≤ DN 1200 0 to +4,5
>DN 1200 0 to +6,0

Bore diameter d1
01, 02 ≤DN 100 0 to +0,5
>DN 100 ≤ DN 400 0 to +1,0
>DN 400 ≤ DN 600 0 to +1,5
>DN 600 0 to +3,0
Wall thickness S 11  
Machined neck machined or (both faces)
Neck one face machined or unmachined
≤DN 100
0 to +1,0
0 to +2,0
≤DN 100
0 to +1,5
0 to +2,5
≤DN 100
0 to +2,0
0 to +3,5

Outside diameter D
01, 02, 05, 11, 13 ≤DN 150 ±2,0
>DN 150 ≤ DN 500 ±3,0
>DN 500 ≤ DN 1200 ±5,0
>DN 1200 ≤ DN 1800 ±7,0
>DN 1800 ±10,0

Length through hub h1
11 ≤DN 80 ±1,5
>DN 80 ≤ DN 250 ±2,0
>DN 250 ±3,0

Neck diameter d3
11 ≤DN 50 0 to -2,0
>DN 50 ≤ DN 150 0 to -4,0
>DN 150 ≤ DN 300 0 to -6,0
>DN 300 ≤ DN 600 0 to -8,0
>DN 600 ≤ DN 4000 0 to -10,0

Neck diameter d3
13 ≤DN 50 0 to +1,0
>DN 50 ≤ DN 150 0 to +2,0
>DN 150 ≤ DN 300 0 to +4,0
>DN 300 ≤ DN 600 0 to +8,0
>DN 600 ≤ DN 1200 0 to +12,0
>DN 1200 ≤ DN 1800 0 to +16,0
>DN 1800 0 to +20,0

Flange thickness b
All types (machined on both faces) ≤18 mm thickness -1,3 to +1,0
>18mm ≤50mm thickness ±1,5
> 50 mm thickness ±2,0

Flange thickness b
All types (machined on front face only) Type 02 and 04 (un- machined) ≤18 mm thickness -1,3 to +2,0
>18mm ≤50mm thickness -1,5 to +4,0
> 50 mm thickness -2,0 to +7,0

Diameter of bolt circle K
01, 02, 05, 11, 13 Bolt sizes M10 to M24 ±1,0
Bolt sizes M27 to M45 ±1,5

Center-to-center of adjacent bolt holes
01, 02, 05, 11, 13 Bolt sizes M10 to M24 ±1,0
Bolt sizes M27 to M45 ±1,5

Eccentricity of machined facing diameters
01, 02, 05, 11, 13 ≤ DN 65 1,0
> DN 65 2,0
Type 01 - Plate Flanges Type 02 - Plate Flanges Type 05 - Plate Flanges Type 11 - Plate Flanges Type 13 - Threaded Flanges


Informationen anfordern

EN1092-1/01B PN10

Check the form
Privacy policy

Personal details provided by filling in this form will be processed by Zetamec srl, with registered offices at Via Fiorelle 28/30 - 36060 Romano d'Ezzelino (Vicenza) - Italy, in such a way as to guarantee the security and confidentiality of the same, and in compliance with the requirements of the law governing privacy and the protection of personal data (Italian Legislative Decree 196/2003). Such data will be consulted and processed on paper or in electronic form in a controlled-access environment. Personal details may be distributed to relevant personnel within company for the following purposes: market research, promotions and commercial information, etc.. Your details may also be distributed by Zetamec srl as process owner to other associated companies or third parties for the same purposes. The provision of your personal details is entirely voluntary, but failure to provide them will make it impossible for us to comply with your request for information. You may, at any time, request that your personal details be updated, modified, added to, or deleted in accordance with Article 7 of Italian Legislative Decree 196/2003, by sending an e-mail to the following address: info@zetamec.com