EN1092-1/05A PN16

Bridas de acero inoxidable 304

EN1092-1/05A PN16 Bridas Ciegas en acero inoxidable. ( UNI 6093 ) ( DIN 2527 )

Technical specification

TOLERANCES (according to UNI 6100-67)

DIMENSION SIZE TOLERANCES
D
Outside diameter
≤ DN 200 ± 1,0
> DN 200 ≤ DN 300 ± 1,5
> DN 300 ≤ DN 400 ± 2,0
> DN 400 ± 2,0
d1
Outside diameter of neck
≤ DN 100 +0,5 -0
> DN 100 ≤ DN 400 +1,0 -0,5
> DN 400 +1,5 -1,0
d1
Bore diameter
≤ DN 80 +0,5 -0
> DN 80 ≤ DN 350 +1,0 -0
> DN 350 ≤ DN 400 +1,5 -0
> DN 400 +5
b
Thickness
≤ DN 10 ± 0,5
> DN 10 ≤ DN 20 ± 0,8
> DN 20 ≤ DN 50 ± 1,0
> DN 50 ± 1,5
d3
Neck diameter
+1 -0
h1
Length through hub
≤ DN 80 ± 1,5
> DN 80 ≤ DN 250 ± 2,0
> DN 250 ± 3,0
S
Wall thickness
≤ DN 100 +1,0 -0
> DN 100 ≤ DN 400 +1,5 -0
> DN 400 +2,0 -0
d4
Diameter of contact face
≤ DN 80 +0 -1,0
> DN 100 ≤ DN 400 +0 -2,0
> DN 400 +0 -3,0
k
Diameter of bolt circle
≤ DN 250 ± 1,5
> DN 250 ≤ DN 600 ± 2,0
> DN 600 ± 3,0
Centre-to-centre of adjacent bolt holes ± 0,4
Max. eccentricity between bolt circle dia. K and machined facing diameters +0,8 -0
Surface parallelism
d2
Holes diameter
≤ DN 300 +2 -0
> DN 30 +3 -0

DIMENSIONAL TOLERANCES (ANSI B 16.5)

D Outside Diameter* Slip-on, Blind and Welding neck flanges When OD is 24" or less ±1,6 mm
When OD is over 24" ±3,2 mm
J Inside Diameter Slip-on flanges 10" and smaller +0,8 mm
12" and larger +1,6 mm
Inside Diameter** Welding neck flanges 10" and smaller +0,8 mm
12" to 18" +1,6 mm
20" and larger +3,2 mm -1,6 mm
g Diameter of Contact Face Slip-on, Blind and Welding neck flanges 1,6 mm Raised Face ±0,8 mm
6,4 mm Raised Face ±0,5 mm
a Diameter of Hub at Point of Welding Welding neck flanges 5" and smaller +2,4 mm -0,8 mm
6" and larger +4,0 mm -0,8 mm
m Outside Diameter of Hub* Slip-on and Blind flanges 12" and smaller +2,4 mm -1,6 mm
14" and larger ±3,2 mm
Diameter of Hub at Base* Welding neck flanges When Hub Base is 24" or less ±1,6 mm
When Hub Base is over 24" ±3,2 mm
i Drilling and facing Slip-on, Blind and Welding neck flanges Bolt Circle Diameter k 1,6 mm
Center-to-center of adjacent bolt holes ±0,8 mm
mmMax. eccentricity between bolt circle dia. kand machined facing diameters  
 
sizes 2½" and smaller 0,8 mm
sizes 3" and larger 1,6 mm
h Overall Length of Hub Slip-on and Blind flanges 18" and smaller +3,2 mm -0,8 mm
20" and larger +4,8 mm -1,6 mm
Welding neck flanges 10" and smaller ±1,6 mm
12" and larger ±3,2 mm
b Thickness Slip-on, Blind and Welding neck flanges 18" and smaller +3,2 mm
20" and larger +4,8 mm

* This tolerance is not covered by ANSI B 16.5

** Undependent of the tolerances of the measures J and a, the wall thickness shall not be less than 87,5% of the nominal wall thickness

TOLERANCES (according to EN 1092-1:2007)

Dimension Flange type Size Tolerance mm
Outside diameter of neck d1 11 ≤DN 125 0 to +3,0
>DN 125 ≤ DN 1200 0 to +4,5
>DN 1200 0 to +6,0

Bore diameter d1
01, 02 ≤DN 100 0 to +0,5
>DN 100 ≤ DN 400 0 to +1,0
>DN 400 ≤ DN 600 0 to +1,5
>DN 600 0 to +3,0
Wall thickness S 11  
Machined neck machined or (both faces)
Neck one face machined or unmachined
≤DN 100
0 to +1,0
0 to +2,0
≤DN 100
0 to +1,5
0 to +2,5
≤DN 100
0 to +2,0
0 to +3,5

Outside diameter D
01, 02, 05, 11, 13 ≤DN 150 ±2,0
>DN 150 ≤ DN 500 ±3,0
>DN 500 ≤ DN 1200 ±5,0
>DN 1200 ≤ DN 1800 ±7,0
>DN 1800 ±10,0

Length through hub h1
11 ≤DN 80 ±1,5
>DN 80 ≤ DN 250 ±2,0
>DN 250 ±3,0

Neck diameter d3
11 ≤DN 50 0 to -2,0
>DN 50 ≤ DN 150 0 to -4,0
>DN 150 ≤ DN 300 0 to -6,0
>DN 300 ≤ DN 600 0 to -8,0
>DN 600 ≤ DN 4000 0 to -10,0

Neck diameter d3
13 ≤DN 50 0 to +1,0
>DN 50 ≤ DN 150 0 to +2,0
>DN 150 ≤ DN 300 0 to +4,0
>DN 300 ≤ DN 600 0 to +8,0
>DN 600 ≤ DN 1200 0 to +12,0
>DN 1200 ≤ DN 1800 0 to +16,0
>DN 1800 0 to +20,0

Flange thickness b
All types (machined on both faces) ≤18 mm thickness -1,3 to +1,0
>18mm ≤50mm thickness ±1,5
> 50 mm thickness ±2,0

Flange thickness b
All types (machined on front face only) Type 02 and 04 (un- machined) ≤18 mm thickness -1,3 to +2,0
>18mm ≤50mm thickness -1,5 to +4,0
> 50 mm thickness -2,0 to +7,0

Diameter of bolt circle K
01, 02, 05, 11, 13 Bolt sizes M10 to M24 ±1,0
Bolt sizes M27 to M45 ±1,5

Center-to-center of adjacent bolt holes
01, 02, 05, 11, 13 Bolt sizes M10 to M24 ±1,0
Bolt sizes M27 to M45 ±1,5

Eccentricity of machined facing diameters
01, 02, 05, 11, 13 ≤ DN 65 1,0
> DN 65 2,0
Type 01 - Plate Flanges Type 02 - Plate Flanges Type 05 - Plate Flanges Type 11 - Plate Flanges Type 13 - Threaded Flanges


Solicitar información

EN1092-1/05A PN16

Check the form

Purpose of processing
We inform you that the personal data voluntarily provided by you will be processed by Zetamec Srl Unipersonale as personal data controller, for the purpose of:

a) providing the requested service and allowing Zetamec Srl Unipersonale to carry out the survey related to this service;
b) providing you, with your express consent, with commercial and/or promotional information, as well as sending you advertising material or performing direct sales activities or commercial communications on products, services and other activities of Zetamec Srl Unipersonale, or performing market research;
c) profiling, with your express consent, your behaviour, consumption and other habits in the sector in which Zetamec Srl Unipersonale operates, in order to improve the services offered by Zetamec Srl Unipersonale;

d) communicating, with your express consent, the data to related companies or third parties to Zetamec Srl Unipersonale, as well as to Zetamec Srl Unipersonale partner companies for processing, in order to provide commercial and/or promotional information, as well as sending advertising material or performing direct sales activities or interactive commercial communications on products, services and other activities of the aforementioned companies, or to carry out market research activities.

Data processing for any of the aforementioned purposes will be executed via paper-based, computerised or telematic means, whichever is most suitable for ensuring the security and confidentiality of the processed data.

Processing procedure
Personal data will be processed mainly using IT equipment.
The personal data that you voluntarily disclose to Zetamec Srl Unipersonale, however it is transmitted (completion of online forms, email communication, etc.), will be stored in a data handling application of Zetamec Srl Unipersonale exclusively for the purposes indicated above, and for the period stipulated by the relevant legislation.
For the purposes of this paragraph, Zetamec Srl Unipersonale undertakes to observe specific security measures to prevent the loss of data, their illicit or incorrect use and unauthorised access, in full compliance with the laws and regulations.

Compulsory/voluntary provision of data
Personal data is provided voluntarily.
However, the refusal of the interested party to provide personal data for the purposes referred to in points b), c) or d) will make it impossible for the data controller to send commercial offers and information on the company's activity.

Data Controller and Responsible Officer
The Controller for the described processing activities is Zetamec Srl Unipersonale, with headquarters in Via Fiorolle 28/30 - 36060 Romano d'Ezzelino (VI) - Italy.
Processing operations will be carried out by Assignees appointed by the Data Controller and/or the Officer responsible for data processing, who operate under their direct authority in compliance with the instructions received.

Persons/bodies to whom/which personal data may be communicated, or who may access them in their capacity as Responsible Officers or data processing officers
Your data may be disclosed to external companies with which Zetamec Srl Unipersonale may consider collaborating, which, in any case, guarantee the adoption of security and confidentiality criteria equivalent to those adopted by Zetamec Srl Unipersonale, and which operate as external data processing bodies.
Your personal data may be disclosed to third parties to comply with legal obligations, or to comply with orders from public authorities, or to exercise a right in court. Furthermore, subject to your consent, your data may be disclosed to third parties as indicated in point d) of these guidelines.

Rights of the interested party
The interested party has the right to obtain confirmation of the existence of his/her personal data, and of their communication, in an intelligible manner.
The interested party has the right to know the content and the origin of the personal data.
The interested party furthermore has the right to demand:

a) the updating, amendment, or, where he/she has an interest in it, the integration of the data;
b) the deletion, anonymization or blocking of unlawfully processed data, including data that does not need to be retained for the purposes for which it was collected or subsequently processed;
c) confirmation that those to whom the data is communicated or disclosed are notified of the actions referred to under points (a) and (b), including their content, unless the fulfilment thereof proves impossible or involves the use of means that are clearly disproportionate to the right being protected.

The interested party has the right to oppose, in whole or in part:

a) on legitimate grounds, the processing of his/her personal data, even if the data is relevant for the purpose of their collection;
b) the processing of their personal data for the purpose of sending advertising material or for direct sales, or for conducting market research or commercial communications.

In any case, the interested party remains free, at any time, to revoke consent by sending an informal notice to that effect to Zetamec Srl Unipersonale, at info@zetamec.com.

To marketing activities:
i.e. the elaboration and processing of data by Zetamec Srl Unipersonale for the marketing purposes referred to under point b) of these guidelines, via the foreseen processing methods, i.e. paper-based, via automated and telematic means, by ordinary or electronic mail, telephone and any other computerised means.

To profiling activities:
i.e. the elaboration and processing of data by Zetamec Srl Unipersonale for the purposes of profiling referred to in point c) of these guidelines, relating - by way of example and not exhaustive - to consumption and other habits, behaviour, consultation and use of the website.

To communication to third parties for marketing purposes:
i.e. the communication of data to companies connected to Zetamec Srl Unipersonale, as well as to partner companies of the same, which will be able to process them for the marketing purposes referred to in point d) of these guidelines, via the foreseen processing methods, i.e. paper-based, via automated and telematic means, by ordinary or electronic mail, telephone and any other computerised means.

By clicking send button, I confirm that I request the service indicated in point a) of these guidelines; my consent to the processing of data for the purposes of the service, including the processing methods mentioned in these guidelines, including possible processing carried out in EU member states or non-EU countries.